Bdtyk

There are some tutorials to make an access point a WiFi repeater using only the on-board WiFi chip of a Raspberry Pi. But I want to use an additional USB/WiFi dongle as second interface for the up-link to an internet router, in the hope it would simplify the configuration and avoid the limitations of the single interface solution.

How can I setup an access point as WiFi repeater using an additional USB/WiFi dongle?

It is known that the Raspberry Pi can spawn an access point and connect as client to another wifi network simultaneously with its on board wifi chip. How to do that you can look at Access point as WiFi repeater, optional with bridge.

But using a second USB/WiFi dongle is simpler and depending on its hardware it may be possible to avoid the limitations of the single interface solution. With systemd-networkd and wpa_supplicant we have everything on the Raspberry Pi to setup what we want. There is no need to install additional software and fiddle with hostapd and dnsmasq. You have to switch to systemd-networkd and then simply set up wpa_supplicant one time for wlan0 as access point and one time for wlan1 as client. Then configure the interfaces and it's done. For reference I use Raspbian Stretch Lite 2018-11-13 updated with sudo apt update && sudo apt full-upgrade && sudo reboot done at 2019-03-07.

Enable systemd-networkd

For detailed information look at ⁽¹⁾. Here only in short. Execute these commands:

# install helper

rpi ~$ sudo -Es

rpi ~# apt install rng-tools



# disable classic networking

rpi ~# systemctl mask networking.service

rpi ~# systemctl mask dhcpcd.service

rpi ~# mv /etc/network/interfaces /etc/network/interfaces~

rpi ~# sed -i '1i resolvconf=NO' /etc/resolvconf.conf



# enable systemd-networkd

rpi ~# systemctl enable systemd-networkd.service

rpi ~# systemctl enable systemd-resolved.service

rpi ~# ln -sf /run/systemd/resolve/resolv.conf /etc/resolv.conf

Configure wpa_supplicant for wlan0 as access point

To configure wpa_supplicant create these files with your settings for country=, ssid=, psk= and maybe frequency= You can just copy and paste this in one block to your command line beginning with cat and including EOF (delimiter EOF will not get part of the file):

rpi ~# cat > /etc/wpa_supplicant/wpa_supplicant-wlan0.conf <<EOF

country=DE

ctrl_interface=DIR=/var/run/wpa_supplicant GROUP=netdev

update_config=1



network={

    ssid="RPiNet"

    mode=2

    key_mgmt=WPA-PSK

    psk="verySecretPassword"

    frequency=2412

}

EOF



rpi ~# chmod 600 /etc/wpa_supplicant/wpa_supplicant-wlan0.conf

rpi ~# systemctl enable wpa_supplicant@wlan0.service

Configure wpa_supplicant for wlan1 as client

rpi ~# cat > /etc/wpa_supplicant/wpa_supplicant-wlan1.conf <<EOF

country=DE

ctrl_interface=DIR=/var/run/wpa_supplicant GROUP=netdev

update_config=1



network={

    ssid="wlan@hoeft-online.de"

    psk="anotherSecretPassword"

}

EOF



rpi ~# chmod 600 /etc/wpa_supplicant/wpa_supplicant-wlan1.conf

rpi ~# systemctl enable wpa_supplicant@wlan1.service

For the connection to the internet router we use network address translation (NAT). To setup it we extend the service for wlan1 with:

rpi ~# systemctl edit wpa_supplicant@wlan1.service

In the empty editor insert these statements, save them and quit the editor:

[Service]

ExecStartPre=/sbin/iptables -t nat -A POSTROUTING -o wlan1 -j MASQUERADE

ExecStopPost=-/sbin/iptables -t nat -D POSTROUTING -o wlan1 -j MASQUERADE

Configure interfaces

Create these two files:

rpi ~# cat > /etc/systemd/network/08-wlan0.network <<EOF

[Match]

Name=wlan0

[Network]

Address=192.168.4.1/24

IPForward=yes

DHCPServer=yes

[DHCPServer]

DNS=84.200.69.80 84.200.70.40

EOF

Because we don't have a bridge, we need two different subnets. Be aware that the static ip address for the access point wlan0 belongs to another subnet than that from wlan1.

rpi ~# cat > /etc/systemd/network/12-wlan1.network <<EOF

[Match]

Name=wlan1

[Network]

DHCP=yes

EOF

Reboot.

That's it.

references:

[1] Howto migrate from networking to systemd-networkd with dynamic failover