Using an older 200A breaker panel on a 60A feeder circuit from house?
1
I'm in the planning stages of a new workshop/shed build. I plan to run a 60A ciruit from the main panel in the house to a subpanel in the shed.
I recently picked up a used Challenger QM322200 200A breaker panel with about a dozen circuit breakers for a song. Can I use this panel as is, with the stock 200A main breaker as a master shut-off? (I'd relabel the panel as 60A).
If no, where can I find a 60A main breaker to swap into the panel?
Thanks for your help.
circuit-breaker subpanel
asked 4 hours ago
Charles LemonCharles Lemon
62
New contributor
Charles Lemon is a new contributor to this site. Take care in asking for clarification, commenting, and answering.
Check out our Code of Conduct.
|
show 1 more comment
1
I'm in the planning stages of a new workshop/shed build. I plan to run a 60A ciruit from the main panel in the house to a subpanel in the shed.
I recently picked up a used Challenger QM322200 200A breaker panel with about a dozen circuit breakers for a song. Can I use this panel as is, with the stock 200A main breaker as a master shut-off? (I'd relabel the panel as 60A).
If no, where can I find a 60A main breaker to swap into the panel?
Thanks for your help.
circuit-breaker subpanel
asked 4 hours ago
Charles LemonCharles Lemon
62
New contributor
Charles Lemon is a new contributor to this site. Take care in asking for clarification, commenting, and answering.
Check out our Code of Conduct.
Harper or one of the other pros will provide more detail, but there are apparently problems with some Challenger breakers. So it may have been cheap because it was somebody's extra, or it may have been cheap because it was junk. List the type of breakers or post a picture and I'm sure the pros can let you know. As far as 200A vs. 60A, assuming there is a 60A breaker in the main panel for the feed to the subpanel, then you can have any size subpanel because the main breaker is a shutoff switch and not needed as an actual safety breaker.
– manassehkatz
4 hours ago
The panel was a working pull from a renovation - they homeowner upgraded the panel for more circuits. As far as I know, there is no problem with the panel as such. It's not the newest tech, but it all seems solid enough. The panel uses bolt-on BQL type breakers.
– Charles Lemon
4 hours ago
Also keep in mind that since you are doing new work, you may need to have AFCI and/or GFCI protection for various circuits.
– manassehkatz
4 hours ago
1
Yep - If I need to buy a few new breakers, that's fine.
– Charles Lemon
4 hours ago
1
@manassehkatz On panels and breakers, ThreePhaseEel is the expert, and just knows this stuff, or has access to all the right resources. Anything I know I learned from TPE.
– Harper
1 hour ago
|
show 1 more comment
1
1
1
I'm in the planning stages of a new workshop/shed build. I plan to run a 60A ciruit from the main panel in the house to a subpanel in the shed.
I recently picked up a used Challenger QM322200 200A breaker panel with about a dozen circuit breakers for a song. Can I use this panel as is, with the stock 200A main breaker as a master shut-off? (I'd relabel the panel as 60A).
If no, where can I find a 60A main breaker to swap into the panel?
Thanks for your help.
circuit-breaker subpanel
asked 4 hours ago
Charles LemonCharles Lemon
62
New contributor
Charles Lemon is a new contributor to this site. Take care in asking for clarification, commenting, and answering.
Check out our Code of Conduct.
I'm in the planning stages of a new workshop/shed build. I plan to run a 60A ciruit from the main panel in the house to a subpanel in the shed.
I recently picked up a used Challenger QM322200 200A breaker panel with about a dozen circuit breakers for a song. Can I use this panel as is, with the stock 200A main breaker as a master shut-off? (I'd relabel the panel as 60A).
If no, where can I find a 60A main breaker to swap into the panel?
Thanks for your help.
circuit-breaker subpanel
circuit-breaker subpanel
asked 4 hours ago
Charles LemonCharles Lemon
62
New contributor
Charles Lemon is a new contributor to this site. Take care in asking for clarification, commenting, and answering.
Check out our Code of Conduct.
asked 4 hours ago
Charles LemonCharles Lemon
62
New contributor
Charles Lemon is a new contributor to this site. Take care in asking for clarification, commenting, and answering.
Check out our Code of Conduct.
asked 4 hours ago
Charles LemonCharles Lemon
62
New contributor
Charles Lemon is a new contributor to this site. Take care in asking for clarification, commenting, and answering.
Check out our Code of Conduct.
asked 4 hours ago
Charles LemonCharles Lemon
62
asked 4 hours ago
Charles LemonCharles Lemon
62
62
New contributor
Charles Lemon is a new contributor to this site. Take care in asking for clarification, commenting, and answering.
Check out our Code of Conduct.
New contributor
Charles Lemon is a new contributor to this site. Take care in asking for clarification, commenting, and answering.
Check out our Code of Conduct.
Charles Lemon is a new contributor to this site. Take care in asking for clarification, commenting, and answering.
Check out our Code of Conduct.
Harper or one of the other pros will provide more detail, but there are apparently problems with some Challenger breakers. So it may have been cheap because it was somebody's extra, or it may have been cheap because it was junk. List the type of breakers or post a picture and I'm sure the pros can let you know. As far as 200A vs. 60A, assuming there is a 60A breaker in the main panel for the feed to the subpanel, then you can have any size subpanel because the main breaker is a shutoff switch and not needed as an actual safety breaker.
– manassehkatz
4 hours ago
The panel was a working pull from a renovation - they homeowner upgraded the panel for more circuits. As far as I know, there is no problem with the panel as such. It's not the newest tech, but it all seems solid enough. The panel uses bolt-on BQL type breakers.
– Charles Lemon
4 hours ago
Also keep in mind that since you are doing new work, you may need to have AFCI and/or GFCI protection for various circuits.
– manassehkatz
4 hours ago
1
Yep - If I need to buy a few new breakers, that's fine.
– Charles Lemon
4 hours ago
1
@manassehkatz On panels and breakers, ThreePhaseEel is the expert, and just knows this stuff, or has access to all the right resources. Anything I know I learned from TPE.
– Harper
1 hour ago
|
show 1 more comment
Harper or one of the other pros will provide more detail, but there are apparently problems with some Challenger breakers. So it may have been cheap because it was somebody's extra, or it may have been cheap because it was junk. List the type of breakers or post a picture and I'm sure the pros can let you know. As far as 200A vs. 60A, assuming there is a 60A breaker in the main panel for the feed to the subpanel, then you can have any size subpanel because the main breaker is a shutoff switch and not needed as an actual safety breaker.
– manassehkatz
4 hours ago
The panel was a working pull from a renovation - they homeowner upgraded the panel for more circuits. As far as I know, there is no problem with the panel as such. It's not the newest tech, but it all seems solid enough. The panel uses bolt-on BQL type breakers.
– Charles Lemon
4 hours ago
Also keep in mind that since you are doing new work, you may need to have AFCI and/or GFCI protection for various circuits.
– manassehkatz
4 hours ago
1
Yep - If I need to buy a few new breakers, that's fine.
– Charles Lemon
4 hours ago
1
@manassehkatz On panels and breakers, ThreePhaseEel is the expert, and just knows this stuff, or has access to all the right resources. Anything I know I learned from TPE.
– Harper
1 hour ago
Harper or one of the other pros will provide more detail, but there are apparently problems with some Challenger breakers. So it may have been cheap because it was somebody's extra, or it may have been cheap because it was junk. List the type of breakers or post a picture and I'm sure the pros can let you know. As far as 200A vs. 60A, assuming there is a 60A breaker in the main panel for the feed to the subpanel, then you can have any size subpanel because the main breaker is a shutoff switch and not needed as an actual safety breaker.
– manassehkatz
4 hours ago
Harper or one of the other pros will provide more detail, but there are apparently problems with some Challenger breakers. So it may have been cheap because it was somebody's extra, or it may have been cheap because it was junk. List the type of breakers or post a picture and I'm sure the pros can let you know. As far as 200A vs. 60A, assuming there is a 60A breaker in the main panel for the feed to the subpanel, then you can have any size subpanel because the main breaker is a shutoff switch and not needed as an actual safety breaker.
– manassehkatz
4 hours ago
The panel was a working pull from a renovation - they homeowner upgraded the panel for more circuits. As far as I know, there is no problem with the panel as such. It's not the newest tech, but it all seems solid enough. The panel uses bolt-on BQL type breakers.
– Charles Lemon
4 hours ago
The panel was a working pull from a renovation - they homeowner upgraded the panel for more circuits. As far as I know, there is no problem with the panel as such. It's not the newest tech, but it all seems solid enough. The panel uses bolt-on BQL type breakers.
– Charles Lemon
4 hours ago
Also keep in mind that since you are doing new work, you may need to have AFCI and/or GFCI protection for various circuits.
– manassehkatz
4 hours ago
Also keep in mind that since you are doing new work, you may need to have AFCI and/or GFCI protection for various circuits.
– manassehkatz
4 hours ago
1
1
Yep - If I need to buy a few new breakers, that's fine.
– Charles Lemon
4 hours ago
Yep - If I need to buy a few new breakers, that's fine.
– Charles Lemon
4 hours ago
1
1
@manassehkatz On panels and breakers, ThreePhaseEel is the expert, and just knows this stuff, or has access to all the right resources. Anything I know I learned from TPE.
– Harper
1 hour ago
@manassehkatz On panels and breakers, ThreePhaseEel is the expert, and just knows this stuff, or has access to all the right resources. Anything I know I learned from TPE.
– Harper
1 hour ago
|
show 1 more comment
1 Answer
1
active
oldest
votes
4
You can use the 200 amp main as a disconnect it is fine since you will be using a 60 amp breaker in the main panel the wire needs to be sized for 60 amps. As long as the panel is as large as the service panel breaker or larger it would be code compliant.
answered 4 hours ago
Ed BealEd Beal
34.2k12148
add a comment |
Your Answer
StackExchange.ready(function() {
var channelOptions = {
tags: "".split(" "),
id: "73"
};
initTagRenderer("".split(" "), "".split(" "), channelOptions);
StackExchange.using("externalEditor", function() {
// Have to fire editor after snippets, if snippets enabled
if (StackExchange.settings.snippets.snippetsEnabled) {
StackExchange.using("snippets", function() {
createEditor();
});
}
else {
createEditor();
}
});
function createEditor() {
StackExchange.prepareEditor({
heartbeatType: 'answer',
autoActivateHeartbeat: false,
convertImagesToLinks: false,
noModals: true,
showLowRepImageUploadWarning: true,
reputationToPostImages: null,
bindNavPrevention: true,
postfix: "",
imageUploader: {
brandingHtml: "Powered by u003ca class="icon-imgur-white" href="https://imgur.com/"u003eu003c/au003e",
contentPolicyHtml: "User contributions licensed under u003ca href="https://creativecommons.org/licenses/by-sa/3.0/"u003ecc by-sa 3.0 with attribution requiredu003c/au003e u003ca href="https://stackoverflow.com/legal/content-policy"u003e(content policy)u003c/au003e",
allowUrls: true
},
noCode: true, onDemand: true,
discardSelector: ".discard-answer"
,immediatelyShowMarkdownHelp:true
});
}
});
Charles Lemon is a new contributor. Be nice, and check out our Code of Conduct.
draft saved
draft discarded
Sign up or log in
StackExchange.ready(function () {
StackExchange.helpers.onClickDraftSave('#login-link');
var $window = $(window),
onScroll = function(e) {
var $elem = $('.new-login-left'),
docViewTop = $window.scrollTop(),
docViewBottom = docViewTop + $window.height(),
elemTop = $elem.offset().top,
elemBottom = elemTop + $elem.height();
if ((docViewTop elemBottom)) {
StackExchange.using('gps', function() { StackExchange.gps.track('embedded_signup_form.view', { location: 'question_page' }); });
$window.unbind('scroll', onScroll);
}
};
$window.on('scroll', onScroll);
});
Sign up using Google
Sign up using Facebook
Sign up using Email and Password
Post as a guest
Required, but never shown
StackExchange.ready(
function () {
StackExchange.openid.initPostLogin('.new-post-login', 'https%3a%2f%2fdiy.stackexchange.com%2fquestions%2f160204%2fusing-an-older-200a-breaker-panel-on-a-60a-feeder-circuit-from-house%23new-answer', 'question_page');
}
);
Post as a guest
Required, but never shown
1 Answer
1
active
oldest
votes
1 Answer
1
active
oldest
votes
active
oldest
votes
active
oldest
votes
4
You can use the 200 amp main as a disconnect it is fine since you will be using a 60 amp breaker in the main panel the wire needs to be sized for 60 amps. As long as the panel is as large as the service panel breaker or larger it would be code compliant.
answered 4 hours ago
Ed BealEd Beal
34.2k12148
add a comment |
4
You can use the 200 amp main as a disconnect it is fine since you will be using a 60 amp breaker in the main panel the wire needs to be sized for 60 amps. As long as the panel is as large as the service panel breaker or larger it would be code compliant.
answered 4 hours ago
Ed BealEd Beal
34.2k12148
add a comment |
4
4
4
You can use the 200 amp main as a disconnect it is fine since you will be using a 60 amp breaker in the main panel the wire needs to be sized for 60 amps. As long as the panel is as large as the service panel breaker or larger it would be code compliant.
answered 4 hours ago
Ed BealEd Beal
34.2k12148
You can use the 200 amp main as a disconnect it is fine since you will be using a 60 amp breaker in the main panel the wire needs to be sized for 60 amps. As long as the panel is as large as the service panel breaker or larger it would be code compliant.
answered 4 hours ago
Ed BealEd Beal
34.2k12148
answered 4 hours ago
Ed BealEd Beal
34.2k12148
answered 4 hours ago
Ed BealEd Beal
34.2k12148
answered 4 hours ago
Ed BealEd Beal
34.2k12148
34.2k12148
add a comment |
add a comment |
Charles Lemon is a new contributor. Be nice, and check out our Code of Conduct.
draft saved
draft discarded
Charles Lemon is a new contributor. Be nice, and check out our Code of Conduct.
Charles Lemon is a new contributor. Be nice, and check out our Code of Conduct.
Charles Lemon is a new contributor. Be nice, and check out our Code of Conduct.
Thanks for contributing an answer to Home Improvement Stack Exchange!
- Please be sure to answer the question. Provide details and share your research!
But avoid …
- Asking for help, clarification, or responding to other answers.
- Making statements based on opinion; back them up with references or personal experience.
To learn more, see our tips on writing great answers.
draft saved
draft discarded
Sign up or log in
StackExchange.ready(function () {
StackExchange.helpers.onClickDraftSave('#login-link');
var $window = $(window),
onScroll = function(e) {
var $elem = $('.new-login-left'),
docViewTop = $window.scrollTop(),
docViewBottom = docViewTop + $window.height(),
elemTop = $elem.offset().top,
elemBottom = elemTop + $elem.height();
if ((docViewTop elemBottom)) {
StackExchange.using('gps', function() { StackExchange.gps.track('embedded_signup_form.view', { location: 'question_page' }); });
$window.unbind('scroll', onScroll);
}
};
$window.on('scroll', onScroll);
});
Sign up using Google
Sign up using Facebook
Sign up using Email and Password
Post as a guest
Required, but never shown
StackExchange.ready(
function () {
StackExchange.openid.initPostLogin('.new-post-login', 'https%3a%2f%2fdiy.stackexchange.com%2fquestions%2f160204%2fusing-an-older-200a-breaker-panel-on-a-60a-feeder-circuit-from-house%23new-answer', 'question_page');
}
);
Post as a guest
Required, but never shown
Sign up or log in
StackExchange.ready(function () {
StackExchange.helpers.onClickDraftSave('#login-link');
var $window = $(window),
onScroll = function(e) {
var $elem = $('.new-login-left'),
docViewTop = $window.scrollTop(),
docViewBottom = docViewTop + $window.height(),
elemTop = $elem.offset().top,
elemBottom = elemTop + $elem.height();
if ((docViewTop elemBottom)) {
StackExchange.using('gps', function() { StackExchange.gps.track('embedded_signup_form.view', { location: 'question_page' }); });
$window.unbind('scroll', onScroll);
}
};
$window.on('scroll', onScroll);
});
Sign up using Google
Sign up using Facebook
Sign up using Email and Password
Post as a guest
Required, but never shown
Sign up or log in
StackExchange.ready(function () {
StackExchange.helpers.onClickDraftSave('#login-link');
var $window = $(window),
onScroll = function(e) {
var $elem = $('.new-login-left'),
docViewTop = $window.scrollTop(),
docViewBottom = docViewTop + $window.height(),
elemTop = $elem.offset().top,
elemBottom = elemTop + $elem.height();
if ((docViewTop elemBottom)) {
StackExchange.using('gps', function() { StackExchange.gps.track('embedded_signup_form.view', { location: 'question_page' }); });
$window.unbind('scroll', onScroll);
}
};
$window.on('scroll', onScroll);
});
Sign up using Google
Sign up using Facebook
Sign up using Email and Password
Post as a guest
Required, but never shown
Sign up or log in
StackExchange.ready(function () {
StackExchange.helpers.onClickDraftSave('#login-link');
var $window = $(window),
onScroll = function(e) {
var $elem = $('.new-login-left'),
docViewTop = $window.scrollTop(),
docViewBottom = docViewTop + $window.height(),
elemTop = $elem.offset().top,
elemBottom = elemTop + $elem.height();
if ((docViewTop elemBottom)) {
StackExchange.using('gps', function() { StackExchange.gps.track('embedded_signup_form.view', { location: 'question_page' }); });
$window.unbind('scroll', onScroll);
}
};
$window.on('scroll', onScroll);
});
Sign up using Google
Sign up using Facebook
Sign up using Email and Password
Sign up using Google
Sign up using Facebook
Sign up using Email and Password
Post as a guest
Required, but never shown
Required, but never shown
Required, but never shown
Required, but never shown
Required, but never shown
Required, but never shown
Required, but never shown
Required, but never shown
Required, but never shown
Harper or one of the other pros will provide more detail, but there are apparently problems with some Challenger breakers. So it may have been cheap because it was somebody's extra, or it may have been cheap because it was junk. List the type of breakers or post a picture and I'm sure the pros can let you know. As far as 200A vs. 60A, assuming there is a 60A breaker in the main panel for the feed to the subpanel, then you can have any size subpanel because the main breaker is a shutoff switch and not needed as an actual safety breaker.
– manassehkatz
4 hours ago
The panel was a working pull from a renovation - they homeowner upgraded the panel for more circuits. As far as I know, there is no problem with the panel as such. It's not the newest tech, but it all seems solid enough. The panel uses bolt-on BQL type breakers.
– Charles Lemon
4 hours ago
Also keep in mind that since you are doing new work, you may need to have AFCI and/or GFCI protection for various circuits.
– manassehkatz
4 hours ago
1
Yep - If I need to buy a few new breakers, that's fine.
– Charles Lemon
4 hours ago
1
@manassehkatz On panels and breakers, ThreePhaseEel is the expert, and just knows this stuff, or has access to all the right resources. Anything I know I learned from TPE.
– Harper
1 hour ago